Articole ştiinţifice

Lucrări reprezentative publicate în reviste cotate ISI

  1. Stan, F., Stanciu, N. V., Fetecau, C., Sandu, I., L., 2019, Mechanical recycling of low-density polyethylene/carbon nanotube composites and its effect on material properties. Journal of Manufacturing Science and Engineering  (IF 2,578) 141 (9), 091004.
  2. Stanciu, N., V., Stan, F., Sandu, I., L., Susac, F., Fetecau, C., Rosculet, R., T., 2019, Mechanical, Electrical and Rheological Behavior of Ethylene-Vinyl Acetate/Multi-Walled Carbon Nanotube Composites. Polymers 2019 (IF 3,164), 11(8), 1300; https://doi.org/10.3390/polym11081300.
  3. Stan, F., Rosculet, R., T., Fetecau, C., 2019, Direct Current method with reversal polarity for electrical conductivity measurement of TPU/MWCNT composites. Measurement, ISSN: 0263-224, 136 (2019), (IF 2,218), pp. 345–355. (Q1, IF 2017: 2.218) ISSN 0263-2241.
  4. Stan F., Stanciu N.V., Fetecău C., 2017, Melt Rheological Properties of Ethylene-Vinyl Acetate/ Multi-Walled Carbon Nanotube Composites, Composites Part B, 110 (2017), (IF 2015: 3.850), pp. 20-31.
  5. Quadrini, F., Bellisario, D., Santo, L., Stan, F., Fetecǎu, C., 2017, Compression molding of thermoplastic nanocomposites filled with MWCNT. Polymers & Polymer Composites, POLYM POLYM COMPOS, Volume 25, nr. 8, ISSN: 0967-3911 (IF 0,256) pp. 611-620.
  6. Stan F., Sandu I.L., Fetecău C., Rosculet R.T., 2017, Effect of reprocessing on the rheological, electrical and mechanical properties of polypropylene/carbon nanotube composites. Journal of Micro and Nano-Manufacturing, 5(2), 021005-021005-9 (9 pages), ISSN 2166-0468 doi:10.1115/1.4035955 [WOS: 000399391900005].
  7. Cantaragiu, A.M., Fetecău, C., Paraschiv, G., 2015, Effect of Carbon Nanotubes Concentration on Creep Behaviour of Polypropylene-Carbon Nanotubes Nanocomposites. Materiale Plastice, Vol. 52(1), pp. 69 -74. (IF 2014: 0.824).
  8. Stan, F., Sandu, I.L., Fetecău, C., 2014, Effect of processing parameters and strain rate on mechanical properties of carbon nanotube-filled polypropylene nanocomposites. Composites: Part B, Vol. 59, pp.109-122 (IF 2014: 2,983).
  9. Vasile, Gh., Fetecău, C., Serban, Al., 2014, Experimental research on the roughness of surfaces processed by milling polyamide composites. Materiale Plastice, Vol. 51(2), pp. 205-212 (IF 2014: 0.824).
  10. Stan F., Fetecău, C., 2013, Characterization of viscoelastic properties of molybdenum disulphide filled polyamide by indentation. Mechanics of Time-Dependent Materials, Vol. 17(2), pp. 205-221 (IF 2014:1,587).
  11. Stan F., Fetecău, C., 2013, Study of stress relaxation in polytetrafluoroethylene composites by cylindrical macroindentation. Composites: Part B, Vol. 47, pp. 298-307 (IF 2014: 2,983).
  12. Stan F., Dobrea, D., Fetecău, C., Antoniac, I., Belea, R., 2013, The effect of processing parameters on the bond strength and electrical conductivity of multi-wall carbon nanotube/low-density polyethylene composite. Journal of Adhesion Science and Technology, Vol. 27(22), pp. 2433-2445 (IF 2014: 0,961).

Lucrări reprezentative publicate în ISI Proceedings

  1. Stan F., Stanciu N.V., Fetecau C., 2019, On the 3D Printability of Multi-Walled Carbon Nanotube/High Density Polyethylene Composites, ASME 2019 14th International Manufacturing Science and Engineering Conference (MSEC2019), 10-14 June, 2019, Pennsylvania State University, The Behrend College, Erie, Pennsylvania, USA.
  2. Fetecau, C., Stan F., Timotin, P., Stanciu, N.,V., Rosculet, R.,T., 2018, Mechanical Behavior of LDPE/MWCNT Composites after Fatigue and Cryogenic Treatment, ASME International Manufacturing Science and Engineering Conference (MSEC 2018), June 18-22, 2018, Texas A&M University (USA).
  3. Stan, F., Fetecău, C., Stanciu, N.V., 2017, Fabrication of Micro-Channels in PMMA by Tip-Based Microfabrication Technique-Depthand Frictin Analisys. Session 2-10-2 Processing and Testing of Polymers and Composites – II, 12th ASME 2016 Manufacturing Science and Engineering Conference (MSEC 2017), June 4-8, 2017, MSEC 2017. University of Southern California, Los Angeles, Ca, USA. 2: Additive Manufacturing; Materials, Paper No. MSEC2017-2763, pp. V002T03A017; 8 pages, doi:10.1115/MSEC2017-2763, ISBN: 978-0-7918-5073-2.
  4. Fetecău, C., Stan, F., Cristea, N.V., Sandu, I.L., 2016, An Analysis of Interfacial Adhesion between TPU/MWCNT Composites and ABS Substrate by Over Injection Molding. Session 2-10-2 Processing and Testing of Polymers and Composites – II, The 11th ASME 2016 Manufacturing Science and Engineering Conference (MSEC2016), MSEC2016-8571. Virginia Tech from June 27 – July 1, 2016, in Blacksburg, Virginia, USA. 1 Article Number: UNSP V001T02A050 Published: 2016.
  5. Fetecău, C., Stan, F., Sandu, I.L, Susac, F., 2015, Tuning the Mechanical Properties of High-Density Polyethylene by ECAE Process. Proceedings of the ASME 10th International Manufacturing Science and Engineering Conference, MSEC 2015, June 08-12, 2015 Charlotte, NC (USA), Vol. 1, Article Number: V001T02A053 [Web of Science].
  6. Stan, F., Sandu, I.L., Fetecău, C., 2015, Investigation on the Effect of Carbon Nanotubes Concentration on the Electrical and Rheological Properties of PP/MWCNTs Composites. Proceedings of the ASME 10th International Manufacturing Science and Engineering Conference, MSEC2015, June 08-12, 2015 Charlotte, NC (USA), Vol. 1, Article Number: V001T02A059 [Web of Science].
  7. Stan, F., Fetecău, C., 2014, Experimental investigation of the adhesion between thermoplastic polyurethane and Acrylonitrile-Butadiene-Styrene substrate. Proceedings of the ASME 2014 International Manufacturing Science and Engineering Conference, MSEC 2014, June 9-13, 2014, Detroit, Michigan, USA [Web of Science].
  8. Stan, F., Fetecău, C., Sandu I.L., 2014, In-mold monitoring of temperature and cavity pressure during the injection molding process. Proceedings of the ASME 2014 International Manufacturing Science and Engineering Conference, MSEC2014, June 9-13, 2014, Detroit, Michigan, USA [Web of Science]
  9. Stan, F., Vlad, D., Fetecău, C., 2013, Statistical Cutting Force Model for Orthogonal Cutting of Polytetrafluoroethylene (PTFE) Composites. ASME 2013 International Manufacturing Science and Engineering Conference, Vol. 1: Processing, ISBN: 978-0-7918-5545-4, Paper No. MSEC2013-1033, Article Number: V001T01A022, 8 p. [Web of Science].
  10. Sandu, I.L., Stan, F., Fetecău, C., 2013, Correlation between Mechanical Properties in Standard Test Specimens and Injection Molded Thin-Wall Parts. ASME 2013 International Manufacturing Science and Engineering Conference, Vol. 1: Processing, ISBN: 978-0-7918-5545-4, Paper No. MSEC2013-1032, Article Number: V001T01A065, 10 pp. [Web of Science].
  11. Fetecău, C., Stan F., Dobrea, D., Birsan, C, 2011, Influence of Injection Molding Parameters on Mechanical Properties of Low Density Polyethylene Filled with Multiwalled Carbon Nanotubes. ASME 2011 International Mechanical Engineering Congress and Exposition, IMECE 2011, 8, 599-605, ISBN: 978-0-7918-5494-5 [Web of Science].
  12. Stan, F., Munteanu, A., Fetecău, C., 2010, Viscoelastic Characterization of Polytetrafluoroethylene (PTFE) Polymer by Sharp Indentation. AIP Conference Proceedings, 1315, 221-226, ISBN 978-0-7354-0871-5, Editor(s): Francisco Chinesta, Yvan Chastel, Mohamed El Mansori [Web of Science].

Articole reprezentative publicate în reviste de specialitate de circulaţie internaţională recunoscute

  1. Stan, F., Stanciu, N., V., Sandu, I., L., Fetecau, C., Serban, Al., 2019, Effect of low- and extreme- low temperature on mechanical properties of 3D printed polyethylene terephthalate glycol copolymer. Ro. J. Techn. Sci. – Appl. Mechanics, Vol. 64, N° 1, Bucharest,  pp. 21−42.
  2. Sandu, I. L., Rosculet, R., Fetecău C., 2016, Effect of Annealing on the Mechanical and Electrical Behavior of Polyurethane/Multi-Walled Carbon Nanotube Nanocomposites, TRANS TECH PUBLICATINS Ltd Switzerland, Key Engineering Materials Vol 699 ISBN 978-3-03835-557-1, 2016, pp. 8-17, (DOI 10.4028/www.scientific.net/KEM.669.8).
  3. Sandu I.L., Rosculet, R.,., Fetecău C., 2016, Rheological Properties of Thermoplastic Polyurethane/Multi-Walled Carbon Nanotube Nanocomposites, TRANS TECH PUBLICATINS Ltd Switzerland, Key Engineering Materials Vol 699, 2016, ISBN 978-3-03835-557-1, pp. 18-24, (DOI 10.4028/www.scientific.net/KEM.669.18).
  4. Sandu, I.L., Stan, F., Fetecău, C., 2013, Study of Flow Font Advancement during Filling Stage of a Spiral Mold, Applied Mechanics and Materials, Vol. 371, 434-438 (DOI 10.4028/www.scientific.net/AMM.371.534).
  5. Munteanu, A., Fetecău, C., Stan, F., 2008, The influence of Cutting Tool Geometry on Surface Quality of Cestilene HD 500 Thermoplastic. Academic Journal of Manufacturing Engineering, Vol. 6(2), ISSN 1583-7904, pp. 87-92.
  6. Postolache, I., Fetecău, C., 2008, Computer Simulation of 3D Filling, Packing and Cooling Process in Injection Molded Acetabular Cup. Academic Journal of Manufacturing Engineering, Vol. 6(3), ISSN 1583-7904, pp. 144-149.
  7. Munteanu, A., Stan, F., Fetecău, C., 2008, New-Machinability Study of Turning Thermoplastic Materials. 12th International Conference – TMCR-2008, Iaşi, România, May 29-31, 2008, În: Buletinul Institutului Politehnic din Iaşi, Tomul LIV (LVIII), Fascicula 1-3, Secţiunea Construcții de Mațini, ISSN 1011-2855, pp.491-498.
  8. Postolache, I., Fetecău, C., Stan, F., 2008, A Comparative Study of Runner Systems Used For Injection Molding of a Complex Part. 12th International Conference – TMCR-2008, Iaşi, România, May 29-31, 2008, În: Buletinul Institutului Politehnic din Iași, Tomul LIV (LVIII), Fascicula 1-3, Secţiunea Construcții de Mașini, ISSN 1011-2855, pp.499-506.
  9. Fetecău, C., Oancea, N., 2002, The Wearing and Durability of Curved-Edged. The Annals of “Dunărea de Jos” University of Galaţi, Technologies in Machine Building, Fascicle V, Anul XX (XXV), ISSN 1221-4566, pp. 67-72.
  10. Blanco, S., Montoya, F., Fetecău, C., 2000, Study of cutting process in end milling by frequency analysis Estudio de la potencia especifica de corte instantanea y su aplication a la caracterization de la fuerza de corte. Buletinul Institutului Politehnic din Iaşi, Tomul XLVI (L), Supliment I, ISSN 1011-2855, pp. 117-120.
  11. Oancea, N., Neagu, M., Fetecău, C., 2000, Modeling of helical surface generation at axy-simmetric tools. Buletinul Institutului Politehnic din Iaşi, Tomul XLVI (L), Supliment I, ISSN 1011-2855, pp. 81-86.
  12. Fetecău, C., Stan, F., Lungu, A., Banu, M., 1999, Fenomene termice in procesul de burghiere. Revista “Construcţia de maşini”, nr. 1-2, Bucureşti, Anul 51, ISSN 0573-7419, pp. 103-105.

Articole reprezentative publicate în volumele unor manifestări ştiinţifice naționale

  1. Stanciu, N., V.,Stan, F., Fetecau, C., Serban, Al., 2018, Fabrication and Characterization of LDPE and HDPE Filaments For 3D Printing. Zilele Academiei de Științe Tehnice din România – ZASTR 18-19 octombrie 2018, Universitatea Petrol-Gaze din Ploiesti
  2. Rosculet, R., T., Fetecău, C., 2017, Techniques for Rapid Prototyping of Scale Models of Blades For Wind Turbines. A 12-a ediţie a Conferinţei „Zilele Academiei de Ştiinţe Tehnice din România”, în perioada 6-7 octombrie 2017, Universitatea Ovidius Constanța„Sinergii strategice în Bazinul Mării Negre. Journal of Engineering Sciences and Innovation, A, Mechanical Engineering, Volume 3, Issue 1/2018, pp. 15-24.
  3. Balanescu, D.,Fetecău, C., 2017, Sense pedagogy through humanities recovered into real sciences. 8th Balkan Region Conference on Engineering & Business Education (BRCEBE) & 10th International Conference on Engineering & Business Education (ICEBE). 19 – 22 October 2017, Sibiu, Romania. Proceedings of the BRCEBE-ICEBE’17 Conference, Sibiu, Romania
  4. Rosculet, R.T., Fetecău, C., 2017, Techniques for rapid prototyping of scale models of blades for wind turbines. A 12-a ediţie a Conferinţei „Zilele Academiei de Ştiinţe Tehnice din România”, în perioada 6-7 octombrie 2017, Universitatea Ovidius Constanța„Sinergii strategice în Bazinul Mării Negre. PROCEEDINGS „Zilele Academice ale ASTR”, ediţia a XII-a 2017, ISSN 2066-6586.
  5. Vlad, D.V., Fetecău, C., Baroiu, N., 2011, FEM analisys of thermal behavior during turning of steel AISI 1040 and AISI 4140. Proceedings of The 15th International Conference Modern Technologies, Quality and Innovation – ModTech – 2011; 25-27 May 2011 (ISI), Valul lui Vodă, Chişinău, Republic of Moldova, ISSN 2066-3919, vol I, pg. 1157-1160.
  6. Santo, L., Quadrini, F., Stan, F., Fetecău, C., 2009, Improvement of performances of hand laminated composites by fiber pre-heating. În: Proceeding of The 2nd International Conference on Polymers Processing in Engineering, PPE 2009, Galaţi, Romania, 22-23 October, 2009, ISSN 2066-9984, pp.48-55.
  7. Postolache, I, Fetecău, C., Quadrini, F., Squeo, E.A., Morarescu, C., 2009, Aspects of injection molding simulation of complex parts. ModTech International Conference – New face of TMCR Modern Technologies, Quality and Innovation – New face of TMC, Iaşi, România 21-23rd Proceedings of The 13th International Conference Modern Technologies, Quality and Innovation, Editura POLITEHNIUM a Universităţii tehnice “Gh. Asachi” din Iaşi, ISSN 2066-3919, pp. 511-514.
  8. Fetecău, C., Stan, F., Dobrea, D., Giurgea, C., 2007, Aspects Concerning Dynamic Modelling of the Hip Joint, 13rd International Conference of Nonconventional Technogies, ICNeT 2007, Iaşi, Romania, May 17-18. Nonconvetional Technologies Review, No. 2/2007, Editura PIM Iaşi, ISSN – 1454-3087, pp. 31-36.
  9. Fetecău, C., Gheorghies, C, Stan, F., Gheorghies, L, 2007, Effect of the Machining Parameters on the Quality of the Surface Finish of Thermoplastic Materials. 2nd International Conference Polymers & Moulds Innovations 2007, 18-21 Aprilie 2007 University College Ghent, Belgium. Lucrarea se afla pe CDul cu lucrarile conferintei PMI 2007, 723.htm, Copyright 2007, Hogeschool Gent, 5 p.
  10. Fetecău, C., Stan, F., Prună, G., Negru, V., 2006, Modelelarea şi simularea injectăriireperului „Ventilator’. Conferinta stiintifica „Ingineria Prelucrării Polimerilor”, Oradea, 26-27 octombrie. Volum de comunicări, Editura PRINTECH, Bucureşti, ISBN 073-718-548-X; ISBN 978-973-718-548-8, pp. 59-65.
  11. San Juan, M., Felipe Montoya, F., Fetecău, C., 2000, Some aspects of the dynamic study of cutting forces. II International Seminar on Improving Machine Tool Performance, July, 3-5, 2000, La Baule, FRANCE. Proceedings, pp. 1-18.
  12. Blanco, S.J., Fetecău, C., Montoya, F.M., 1998, Incidencia del desgaste y la rotura de la herramienta en el espectro de las fuerzas de corte en fresado. XII Congreso de MAaquinas – Herramienta Y Technologias de Fabricasion, San Sebastian, Espania, 29 – 30 de Octubre de 1998, pp. 387-399.